 For use in industrial and municipal water/wastewater, well usage monitoring, cooling tower water treatment
3, 4, 6, 8, 10, and 12" pipe sizes
Simple as a mechanical meter
No moving parts
Built-in pulse output
Minimal straight pipe
Battery or external power
Solar compatible
Data logger compatible
Telemetry-ready
|
The WMX-Series are fanged electromagnetic fowmeters for use in 4” to 10” pipe in municipal or industrial water and wastewater
applications where propeller meters have typically been used in the past. Because the WMX has no moving parts and has
electrodes designed to discourage fouling, this magmeter performs well and requires much less frequent maintenance
in applications where debris would impede propeller meters. There is no rotor to stop turning or bearings to wear out. Minimal
straight pipe requirements allow WMX-Series meters to be used in piping confgurations where there is little space between the
meter and an elbow.In chemical injection applications, the meter should be placed upstream of the injection line or far enough downstream for thorough mixing to occur before the meter.Rate and total indication are standard on both models. Units
are customer-selected and factory-set. No set-up is required.The WMX101 is externally powered with 7-26 Vdc at 30 mA max
(see NOTE in Specifcations). Two Lithium 3.6V “AA” batteries provide auxiliary power during power failures, allowing the meter
to continue recording fow rate and total without interruption for the duration of the outage. Where external power loss is
infrequent, battery life should exceed 10 years.
applications where propeller meters have typically been used in the past. Because the WMX has no moving parts and has
electrodes designed to discourage fouling, this magmeter performs well and requires much less frequent maintenance
in applications where debris would impede propeller meters. There is no rotor to stop turning or bearings to wear out. Minimal
straight pipe requirements allow WMX-Series meters to be used in piping confgurations where there is little space between the
meter and an elbow.In chemical injection applications, the meter should be placed upstream of the injection line or far enough downstream for thorough mixing to occur before the meter.Rate and total indication are standard on both models. Units
are customer-selected and factory-set. No set-up is required.The WMX101 is externally powered with 7-26 Vdc at 30 mA max
(see NOTE in Specifcations). Two Lithium 3.6V “AA” batteries provide auxiliary power during power failures, allowing the meter
to continue recording fow rate and total without interruption for the duration of the outage. Where external power loss is
infrequent, battery life should exceed 10 years.
The 20-foot power cable also provides pulse output for use with a variety of Seametrics and other displays and controls for
remote reading, data logging, pulse-to-analog conversion, and telemetry applications. High frequency pulse rate (required for
use with 4-20 mA converters) is standard; additional pulse rates are optional.
The WMX104 is a battery-operated unit for use when pulse output is not required. The Lithium 3.6V “D” batteries are
replaceable with an approximate 1-year life under continuous use, or more depending on the duty cycle. An optional input/
output cable can be installed post-factory if needed for changing applications.
remote reading, data logging, pulse-to-analog conversion, and telemetry applications. High frequency pulse rate (required for
use with 4-20 mA converters) is standard; additional pulse rates are optional.
The WMX104 is a battery-operated unit for use when pulse output is not required. The Lithium 3.6V “D” batteries are
replaceable with an approximate 1-year life under continuous use, or more depending on the duty cycle. An optional input/
output cable can be installed post-factory if needed for changing applications.
FEATURES
• Simple and economical as a
mechanical meter
• No moving parts
• Built-in pulse output
• Minimal straight pipe required
• Continuous battery or external power
• Data logger compatible
• Telemetry-ready
• Simple and economical as a
mechanical meter
• No moving parts
• Built-in pulse output
• Minimal straight pipe required
• Continuous battery or external power
• Data logger compatible
• Telemetry-ready
APPLICATIONS
• Municipal water/wastewater
• Industrial water/wastewater
• Cooling tower water treatment
• Well usage reporting
Tidak ada komentar:
Posting Komentar